| 公司提供的商品及其编码 |
76151090 10 铝制高压锅 (包饺子器)
84812020 00 气压传动阀
84814000 00 安全阀或溢流阀
85094010 00 水果或蔬菜的榨汁机
87083092 00 大型客车用制动器及其零件
|
AIR BRAKE SYSTEMS
Air Preparation Systems
 Dehydrator 11.3511010-01
Description
Dehydrator 11.3511010-01 is used in Air Brake Systems of trucks, buses, tractors and other vehicles. It is used for air drying and automatic moisture drainage.
When air pressure grows up to 1.1 MPa and then reduces to 0.8 MPa, atmospheric moisture capacity of the air, supplied into braking system, does not exceed 90…95%, excluding the possibility of system failure caused by condensate freezing.
The Dehydrator makes any additional anti-freezing systems unnecessary.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Drain: automatic
Dehydration efficiency, %, not less than: 75
Thread, mm: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 2,55
Pressure Control Valve 11.3512010
Description
Pressure Control Valve 11.3512010 is used in Air Brake Systems of trucks, buses, wheeled tractors and other vehicles.
Provides pressure control of the air, supplied by compressor into the receivers of pneumatic system. Features a safety valve, which ensures that the resulting pressure does not exceed a specific value.
Technical specification
ON pressure, MPa (kgs/cm2), not less than: 0,65 (6,5)
OFF pressure, MPs (kgs/cm2): 0,85±0,02 (8,5±0,2)
Relief valve engagement pressure, MPa (kgs/cm2): from 0,9 to 1,05 (from 9 to 10,5)
Thread, mm: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,865
 Pressure Control Valve 11.3512010-10/-20
Description
Pressure Control Valve 11.3512010-10/20 is used in Air Brake Systems of trucks, buses, trolleybuses, wheeled tractors and other commercial vehicles.
Provides pressure control of the air, supplied into vehicle's brake system.
Pressure Control Valve comes with a bracket, allowing installation of Pressure Control Valve 11.3512010-10 as a replacement for 100-3512010 and Pressure Control
Valve 11.3512010-20 as a replacement for 11.3512010.
Main advantages of Pressure Control Valve 11.3512010-10/20 in comparison with Pressure Control Valve 11.3512010 are:
- air-bleed valve
- no compressed air leak when in compressor unload mode
Moving parts, rubber seals and springs of Pressure Control Valve 11.3512010-10/20 are unified with similar parts of Dehydrator with Pressure Regulator 14.3512010.
Technical specification
ON pressure, MPa (kgs/cm2), not less than: 0,65 (6,5)
OFF pressure, MPs (kgs/cm2), not less than: 0,85 (8,5)
Relief valve engagement pressure, MPa (kgs/cm2): from 0,95 to 1,35 (from 9,5 to 13,5)
Thread, mm: M22x1,5
Air bleed valve thread, mm: M16x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,67
 Anti Freezer 11.3515150-11
Description
Anti Freezer 11.3515150-11 is used in Air Brake Systems of trucks, buses and wheeled tractors and other vehicles.
Used for forcing ethanol into the Air Brake System to prevent condensate freezing in the pipelines of the Brake System's devices.
Operated mechanically by pressing the pusher button.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Working medium: air, ethanol
Volume of ethanol, supplied in one injection:
with air pressure in the inlet: 1,0 – 1,5
without air pressure in the inlet: 1,4 – 2,0
Thread, mm: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,55
 Dehydrator with Pressure Regulator 14.3512010
Description
Dehydrator with Pressure Regulator 14.3512010 is used in Air Brake Systems of trucks, buses, trolleybuses, wheeled tractors and other commercial vehicles.
It is used for dehydration, air pressure control and automatic moisture drainage.
Main advantages of Dehydrator with Pressure Regulator 14.3512010 in comparison with Dehydrator 11.3511010-01 are:
20% more effective dehydrating capability for improved safety in low temperature conditions
No compressed air leak when in compressor unload mode (extends compressor's lifetime by reducing its operation recurrence)
Dehydrator's and pressure regulator's features in one device (resulting in 1.2kg reduced steel intensity)
Simplified wiring as a result of reduced connecting armature, piping and bracketry
Mounted on the same bracket as used with Dehydrator 11.3511010-01
Price 15% lower than net price of Dehydrator 11.3511010-01 and Pressure Control Valve 11.3512010
Technical specification
ON pressure, MPa (kgs/cm2), not less than: 0,65 (6,5)
OFF pressure, MPs (kgs/cm2), not less than: 0,85 (8,5)
Relief valve engagement pressure, MPa (kgs/cm2): from 0,95 to 1,35 (from 9,5 to 13,5)
Thread, mm: M22x1,5
Air bleed valve thread, mm: M16x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,67
 Dehydrator with Pressure Regulator 14.3512010-10
Description
Dehydrator with Pressure Regulator 14.3512010-10 is used in Air Brake Systems of trucks, buses, trolleybuses, wheeled tractors and other commercial vehicles.
It is used for dehydration, air pressure control and automatic moisture drainage.
Modification 14.3512010-10 differs from 14.3512010 in longer smooth pipe, used for preventing heat transfer reduction caused by pipe dirtying.
Technical specification
ON pressure, MPa (kgs/cm2), not less than: 0,65 (6,5)
OFF pressure, MPs (kgs/cm2), not more than: 0,85 (8,5)
Relief valve engagement pressure, MPa (kgs/cm2): from 0,95 to 1,35 (from 9,5 to 13,5)
Drain: automatic
Thread, mm: M22x1,5
Air bleed valve thread, mm: M16x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, not more than, kg: 2,5
 Dehydrator with Pressure Regulator 14.3512010-01
Description
Dehydrator with Pressure Regulator 14.3512010-01 is used in Air Brake Systems of trucks, buses, trolleybuses, wheeled tractors and other commercial vehicles.
It is used for dehydration, air pressure control and automatic moisture drainage.
Modification 14.3512010-01 differs from 14.3512010 in the following:
Has a cooler flange joint made of ribbed pipe, which improves mechanical durability and assures maintainability
Has a refined safety-valve duplication system
Changed regulation section and improved reliability of check valve in low temperature conditions
Improved design of bypass channel valve, providing necessary efficiency and longevity
Has a filter in the entrance lag, which ensures protection against foreign particles.
Technical specification
ON pressure, MPa (kgs/cm2), not less than: 0,65 (6,5)
OFF pressure, MPs (kgs/cm2), not more than: 0,85 (8,5)
Relief valve engagement pressure, MPa (kgs/cm2): from 1,15 to 1,4 (from 11,5 to 14,0)
Drain: automatic
Thread, mm: M22x1,5
Air bleed valve thread, mm: M16x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, not more than, kg: 2,75
 Dehydrator with Pressure Regulator 14.3512010-11
Description
Dehydrator with Pressure Regulator 14.3512010-11 is used in Air Brake Systems of trucks, buses, trolleybuses, wheeled tractors and other commercial vehicles.
It is used for dehydration, air pressure control and automatic moisture drainage.
Modification 14.3512010-11 has constructional improvements similar to device 14.3512010-01 and differs in the following:
Air-bleed device with connecting threading M 16x1.5
More effective drying capability resulting from increased pressure (up to 1.0…1.07 MPa or 10…10.7 kg/cm2) produced by compressor before the check valve.
Technical specification
ON pressure, MPa (kgs/cm2), not less than: 0,65 (6,5)
OFF pressure, MPs (kgs/cm2), not more than: 0,85 (8,5)
Relief valve engagement pressure, MPa (kgs/cm2): from 1,15 to 1,4 (from 11,5 to 14,0)
Drain: automatic
Thread, mm: M22x1,5
Air bleed valve thread, mm: M16x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, not more than, kg: 2,7
 Air Dryer 11.3536008/-10
Description
Air Dryer 11.3536008/-10 is to be used in air brake systems of commercial vehicles for the purpose of drying and purifying the compressed air and thus preventing corrosion and condensate freezing in the circuits of the air brake system. Air Dryer improves reliability of other components of the system.
Air Dryer 11.3536008/-10 features built-in pressure regulator, safety valve, heating element, silencer, and preliminary moisture separator, designed to increase the lifespan of cartridge absorber
Technical specification
Compressor atmosphere discharge mode engagement pressure, MPa (kgs/cm2):
for 11.3536008: 0,81+0,02 (8,1+0,2)
for 11.3536008-10: 0,85+0,02 (8,5+0,2)
Compressor fill mode engagement pressure, Mpa (kgs/cm2), min: 0,7 (7,0)
Pressure, limited by safety valve, MPa (kgs/cm2): 0,95+0,2…1,35 (9,5…13,2)
Thread, mm: M22x1,5
Air bleed valve thread, mm: M16x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, not more than, kg: 4,4
Heater element specification
Rated voltage, V:
for 11.3536008: 12+3-1,5
for 11.3536008-10: 24+6-3
Nominal power consumption, W: 100 Turn-on temperature, °C: 7+2-6 Turn-off temperature, °C: 27±4
 Air Dryer Cartridge 11.3536180
Description:
Replacable cartridge for Air Dryer 11.3536008/-10
Technical specification
Working pressure: 800 kPa
Maximum pressure: 1,3 MPa
Thread, mm: M39x1,5
|
Circuit Protection Devices
 Protection Valve Single 100-3515010-01
Description
Protection Valve Single 100-3515010-01 is used in Air Brake Systems of trucks, buses, trolleybuses and wheeled tractors.
It is used for isolating the malfunctioning part of the Air Brake System. Protection Valve Single can be used for separating the pneumatic drive of brake system from second-priority accessory drives.
Valves 100-3515010 and 100-3515010-01 "without upstream" are used for connecting systems, where air upstream (reverse stream) is not permitted.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Feedthrough pressure, MPa (kgs/cm2): 0,5 – 0,56 (5,0 – 5,6)
Thread, mm: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,23
 Protection Valve Single 12-3515010-01
Description
Single Protection Valve 12.3515010-01 is used in Air Brake Systems of trucks, buses, trolleybuses and wheeled tractors.
This valve provides filling of circuits of braking system when certain meaning is reached. When inlet chamber pressure declines, compressed air is delivered from outlet chamber.
Valve 12.3515010-01 with upstream can be used for attachment systems without air upstream limitation.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Feedthrough pressure, MPa (kgs/cm2): 0,5 – 0,56 (5,0 – 5,6)
Thread, mm: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,23
 Double-Main 100-3562010/-01
Description
Double-Main Valve 100-3562010 is used in Air Brake Systems of trucks, buses, wheeled tractors, trailers and semi-trailers.
It has two inputs and one output and provides fast air bypass from the input with bigger pressure to the output.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Thread, mm: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,42
 Circuit Protection Valve Double 100-3515110
Description
Circuit Protection Valve Double 100-3515110 is used in Air Brake Systems of trucks, buses and wheeled tractors.
It is designed to divide the feeder mains into two independent circuits.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Protection pressure in operating circuit, MPa (kgs/cm2), not more than: 0,64 (6,4)
Thread, mm: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,60
 Check Valve 11.3567010
Description
Check Valve 11.3567010 is used in Air Brake Systems of trucks and wheeled tractors.
It is designed to provide one-way pressure air supply without pressure control into a circuit and prevents reverse airflow from that circuit.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Thread, mm: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,06
 Check Valve 11.3567010-10
Description
Check Valve 11.3567010-10 is used in Air Brake Systems of trucks and wheeled tractors.
It is designed to provide one-way pressure air supply without pressure control into a circuit and prevents reverse airflow from that circuit.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Thread, mm: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,06
 Four-circuit Protection Valve 11.3515410
Description
Four-circuit Protection Valve 11.3515410 is used in Air Brake Systems of trucks, buses, trolleybuses and wheeled tractors.
It is designed to split the pneumatic system into four independent circuits and automatically disconnect damaged circuits.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Protection pressure, MPa (kgs/cm2), not lower than: in working circuits: 0,5 (0,5)
Supported air pressure in operating circuits during compressor operation and failure of one of the circuits, MPa (kgs/cm2) - 0,8…0,89 (8,0…8,9)
Thread, mm:
feeding main: M22x1,5
circuit outputs: M16x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 0,730
 Four-circuit Protection Valve 14.3515410
Description
Four-circuit Protection Valve 14.3515410 is used in Air Brake Systems of trucks, buses, trolleybuses and wheeled tractors.
It is designed to split the pneumatic system into four independent circuits and automatically disconnect damaged circuits.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,65...0,85 (6,5...8,5)
Temperature range, °C: from minus 45 to plus 60
Thread, mm:
feeding main: M22x1,5 - 7H
circuit outputs: M16x1,5 - 7H
Weight, kg: 0,730
|
Brake Control Valves
 Two-Section Brake Valve with Lever 100-3514008/-10/-20/-30
Description
Two-Section Brake Valve 100-3514008 is used is Air Brake Systems of trucks, buses, trolleybuses and wheeled tractors.
The Brake Valve is operated mechanically by brake pedal, ensuring fast and controllable admission of compressed air into the brake chambers in each of two circuits, as well as into control chambers of other pneumatic apparatus of the Brake System.
If one of the Brake System's circuits is depressurized, the Brake Valve provides controllable refill of the other circuit with compressed air.
Modification 100-3514008-01/-11/-21/-31 is characterized by possibility to install the Silencer 11.3590070, produced by PJSC PAAZ, and by screen filters availability in feeds “11” and “12”. The positions of lever against air inputs and outputs are similar to 100-3514008/-10/-20/-30.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Free lever stroke, mm: 4,7 – 7,4
Full opening lever stroke, mm: 18,5 – 27
Total lever stroke, mm: 23,1 – 39,1
Thread: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 3,425
 Two-Section Brake Valve with Lever 100-3514008-01/-11/-21/-31
Description
Two-Section Foot Brake Valve for Suspended Pedal 11.3514208-01/-11-/21-/31 is used in Air Brake Systems of trucks, buses, trolleybuses and wheeled tractors.
The Brake Valve is operated mechanically by suspended pedal, ensuring that the brake chambers in each of two circuits, as well as control chambers of other pneumatic apparatus of the Brake System, are filled with compressed air following appropriate filling speed and with appropriate tracking.
If one of the Brake System's circuits is depressurized, the Brake Valve provides controllable (with tracking) refill of the other circuit with compressed air. Given modification is compatible with Silencer produced by PJSC “PAAZ”" and additional filters.
The positions of pedal mechanism against air inputs and outputs are similar to 11.3514208/-10/-20/-30
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Free lever stroke, mm: 4,7 – 7,4
Full opening lever stroke, mm: 18,5 – 27
Total lever stroke, mm: 23,1 – 39,1
Thread: M22x1,5
Temperature range, °C: from minus 45 to plus 60
Weight, kg: 3,425
 Reverse Action Hand Brake Valve with Brake Release Device 11.3537310
Description
Back Action Hand Brake Valve with Brake Release Device 11.3537310 is used in Air Brake Systems of trucks, buses and wheeled tractors.
Allows performing control check of the truck's parking brake efficiency when holding the whole articulated lorry on a slope with trailer's brakes released.
Operated mechanically by turning the handle and provides controlled compressed-air bleed from the parking brake control bus or from the reserve brake control bus.
Technical specification
Working pressure, MPa (kgs/cm2): no more than 0,8 (8,0)
Connecting threading: М14x1.5
Temperature interval, °С: minus 45 to plus 60
Weight, kg: 1.2
 Reverse Action Hand Brake Valve 100-3537010
Description
Reverse Action Hand Brake Valve 100-3537010 is used in Air Brake Systems of trucks, buses, wheeled tractors and other commercial vehicles.
Operated mechanically by turning the handle. Provides controlled compressed-air bleed from the parking brake control bus or from the reserve brake control bus.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Thread: М14Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 0,895
 Two-Section Foot Brake Valve 11.3514108/-10/-20/-30/-01/-11/-21/-31
Description
Two-Section Foot Brake Valve 11.3514108 is used in Air Brake Systems of trucks, buses, and wheeled tractors.
The Brake Valve is operated mechanically by pedal, which is to be installed between valve's lugs, ensuring that the brake chambers in each of two circuits, as well as control chambers of other pneumatic apparatus of the Brake System, are filled with compressed air following appropriate filling speed and with appropriate tracking.
If one of the Brake System's circuits is depressurized, the Brake Valve provides controllable (with tracking) refill of the other circuit with compressed air.
Available modifications:
11.3514108/-10/-20/-30. These modifications differ in the positions of pedal mechanism against air inputs and outputs
Optionally can be equipped with an outlet port for installing Silencer 11.3590070, produced by PJSC "Poltava Automobile Unit Plant" and with screen filter.
Technical specification
Working pressure, MPa (kgs/cm2): 0,65 – 0,85 (6,5 – 8,5)
Свободный ход толкателя, mm: 1,9 – 3,0
Full opening pusher stroke, mm: 8,4 – 10,8
Total pusher stroke, mm: 12,5 – 15,7
Thread: М22X1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 2,70
 Two-Section Foot Brake Valve for Suspended Pedal 11.3514208/-10/-20/-30
Description
Two-Section Foot Brake Valve for Suspended Pedal 11.3514208 is used in Air Brake Systems of trucks, buses, trolleybuses and wheeled tractors.
The Brake Valve is operated mechanically by suspended pedal, ensuring that the brake chambers in each of two circuits, as well as control chambers of other pneumatic apparatus of the Brake System, are filled with compressed air following appropriate filling speed and with appropriate tracking.
If one of the Brake System's circuits is depressurized, the Brake Valve provides controllable (with tracking) refill of the other circuit with compressed air.
Available modifications:
11.3514208/-10/-20/-30. These modifications differ in the positions of pedal mechanism against air inputs and outputs
Technical specification
Working pressure, MPa (kgs/cm2): 0,65 – 0,85 (6,5 – 8,5)
Free pusher stroke, mm: 1,9 – 3,0
Full opening pusher stroke, mm: 8,4 – 10,8
Total pusher stroke, mm: 12,5 – 15,7
Thread: М22X1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 2,70
 Two-Section Foot Brake Valve for Suspended Pedal 11.3514208-01/-11/-21/-31
Description
Two-Section Foot Brake Valve for Suspended Pedal 11.3514208-01/-11-/21-/31 is used in Air Brake Systems of trucks, buses, trolleybuses and wheeled tractors.
The Brake Valve is operated mechanically by suspended pedal, ensuring that the brake chambers in each of two circuits, as well as control chambers of other pneumatic apparatus of the Brake System, are filled with compressed air following appropriate filling speed and with appropriate tracking.
If one of the Brake System's circuits is depressurized, the Brake Valve provides controllable (with tracking) refill of the other circuit with compressed air. Given modification is compatible with Silencer produced by PJSC “PAAZ”" and additional filters.
The positions of pedal mechanism against air inputs and outputs are similar to 11.3514208/-10/-20/-30
Technical specification
Working pressure, MPa (kgs/cm2): 0,65 – 0,85 (6,5 – 8,5)
Free pusher stroke, mm: 1,9 – 3,0
Full opening pusher stroke, mm: 8,4 – 10,8
Total pusher stroke, mm: 12,5 – 15,7
Thread: М22X1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 2,70
 Two-Section Foot Brake Valve 11.3514308-10/-20/-30/-01/-11/-21/-31
Description
Two-Section Foot Brake Valve 11.3514308 is used in Air Brake Systems of trucks, buses, trolleybuses and wheeled tractors.
The Brake Valve is operated mechanically by suspended pedal, ensuring that the brake chambers in each of two circuits, as well as control chambers of other pneumatic apparatus of the Brake System, are filled with compressed air following appropriate filling speed and with appropriate tracking.
If one of the Brake System's circuits is depressurized, the Brake Valve provides controllable (with tracking) refill of the other circuit with compressed air.
Available modifications:
11.3514308/-10/-20/-30. These modifications differ in the positions of pedal mechanism against air inputs and outputs
11.3514308-01/-11/-21/-31. These modifications are compatible with Silencer produced by PJSC "Poltava Automobile Unit Plant" and additional filters.
The positions of pedal mechanism against air inputs and outputs are similar to 11.3514308/-10/-20/-30
Technical specification
Working pressure, MPa (kgs/cm2): 0,65 – 0,85 (6,5 – 8,5)
Free pusher stroke, mm: 1,9 – 3,0
Full opening pusher stroke, mm: 8,4 – 10,8
Total pusher stroke, mm: 12,5 – 15,7
Thread: М22X1,5
Temperature range, °С: from minus 45 to plus 60
 Reverse Action Hand Brake Valve 11.3537410/-10
Description
Reverse Action Hand Brake Valve 11.3537410/-10 is used in Air Brake Systems of trucks, buses, wheeled tractors and other commercial vehicles.
Operated mechanically by turning the handle. Provides controlled compressed-air bleed from the parking brake control bus or from the reserve brake control bus.
Technical specification
Working pressure, MPa (kgs/cm2): 0,65...0,85 (6,5...8,5)
Maximum through passage section, equivalent to the aperture diameter, mm: 7
Thread, mm:
for 11.3537410 - М 14х1,5
for 11.3537410-10 - М 16х1,5
Tightening torque of connecting steel with rubber sealing elements on the screw holes, N•m: 15...25
Working temperature range, °С: from minus 45 to plus 80
Weight, no more than, kg: 0,73
|
Auxiliary Brake System Apparatus
 Pneumatic Valve 100-3537110
Description
Directional Control Valve 100-3537110 is used in Air Brake Systems of trucks, buses and wheeled tractors.
Mechanically operated (without tracking). Ensures entry of compressed air into slave cylinders of Auxiliary Brake System.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Thread: М12Х1,5
Temperature range, °С: from -45 to +60
Weight, kg: 0,24
 Pneumatic Cylinder 35х65 100-3570210
Description
Pneumatic Cylinder 35х65 100-3570210 is used in pneumatic drive of Auxiliary Brake Systems of trucks and wheeled tractors.
It is used for controlling air-gates of auxiliary (engine) brake. Operated pneumatically by the valve of Auxiliary Brake System. Can be used in pneumatic drives of different systems and aggregates.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Cylinder diameter, mm: 35
Rod stroke, mm: 65
Thread: М12Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 0,65
 Pneumatic Cylinder 30х25 11.3570110
Description
Pneumatic Cylinder 30х25 100-3570110 is designed to manage the fuel pump control bar in order to disable fuel feeding when vehicle's auxiliary (engine) brake is enabled.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Cylinder diameter, mm: 30
Rod stroke, mm: 25
Thread: М10Х1
Temperature range, oС: from minus 45 to plus 60
Weight, kg: 0,24
|
Trailer Brake Control Valves
 Double Line Trailer Brake Control Valve 100-3522010
Description
Double Line Trailer Brake Control Valve 100-3522010 is used two-circuit brake systems of trucks and wheeled tractors.
Controlled pneumatically by two-line brake valve and autonomously by hand brake valve or by the valve of auxiliary brake system.
Ensures fast and controllable admission of compressed air into trailer's main line. If one of the carrier's brake circuits is depressurized, the Double Trailer Brake Control Valve controls the properly functioning circuit.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Thread: М22Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 2,1
 Single - line Trailer Brake Control Valve 100-3522110
Description
Single-Line Trailer Brake Control Valves are used in Air Brake Systems of trucks and wheeled tractors.
Operated pneumatically by Two-Line Trailer Brake Control Valve. Ensures fast and controllable air bleeding from the connecting line of the single-line trailer actuator.
Additionally, the valves include a regulating device, which limits the pressure of air, supplied into the trailer's brake gear.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Air pressure in trailer main, MPa (kgs/cm2): 0,5…0,54 (5,0…..5,4)
Thread: М22Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 2,42
 Single - line Trailer Brake Control Valve 100-3522110-10
Description
Single-Line Trailer Brake Control Valves are used in Air Brake Systems of trucks and wheeled tractors.
Operated pneumatically by Two-Line Trailer Brake Control Valve. Ensures fast and controllable air bleeding from the connecting line of the single-line trailer actuator.
Additionally, the valves include a regulating device, which limits the pressure of air, supplied into the trailer's brake gear.
Valve 100-3522110-10 can be controlled mechanically by turning the valve handle. When controlled pneumatically, valve 100-3522110-10 works similarly to valve 100-3522110.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Air pressure in trailer main, MPa (kgs/cm2): 0,5…0,54 (5,0…..5,4)
Thread: М22Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 2,42
 Double Line Trailer Brake Control Valve with Emergency Valve 11.3522008
Description
Double Line Trailer Brake Control Valve with Emergency Valve 11.3522008 is designed to be used in Two Circuit Air Brake System of trucks and wheeled tractors.
Operated pneumatically by Two-Circuit Brake Valve and autonomously by Back Action Hand Brake Valve or by Auxiliary Brake Valve and ensures fast and controllable admission of compressed air into trailer's main line.
Provides automatic trailer's brake action if the main line is depressurized or not connected.
Technical specification
Working pressure, MPa (kg/cm2): no more than 0.85 (8.5)
Connecting threading: М22Х1,5
Temperature interval, °С: minus 45 to plus 60
Weight, kg: 2,6
 Double Line Trailer Brake Control Valve with Emergency Valve 11.3522008-10/-20
Description
Two-Line Trailer Brake Control Valve with Breakage Valve 11.3522008-10/-20 is designed to be used in Two Circuit Air Brake System of trucks and wheeled tractors.
Operated pneumatically by Two-Circuit Brake Valve and autonomously by Back Action Hand Brake Valve or by Auxiliary Brake Valve and ensures fast and controllable admission of compressed air into trailer's main line.
Provides automatic trailer's brake action if the main line is depressurized or not connected.
Technical specification
Working pressure, MPa (kg/cm2): no more than 0.85 (8.5)
Connecting threading: М22Х1,5
Temperature interval, °С: minus 45 to plus 60
Weight, kg: 2,6
|
Air Dispensers and Relay Valves
 Air Dispenser for Two-Line Trailer Brake System 11.3531010-71
Description:
Air Dispenser for Two-Line Trailer Brake System 11.3531010-71 is used in both Two-Line and Combined Air Brake Systems of trailers and semi-trailers. Operated mechanically and ensures fast and controllable admission of compressed air into trailer's brake chambers. Features a mechanically operated valve for automatic trailer brake release.
It is a improved modification of the Air Dispenser 11.3531010-70, distinguishing by discharged valve system, which allows to decrease initial device sensitivity from 0,045 MPa to 0,03 MPa and consequently to decrease trailer (semi-trailer) air brake abrasion time. A distinguishing feature of this device is improved appearance and lesser steel intensity by using injection casting in body production without a price rise in comparison with 11.3531010-70.
Air Dispenser 11.3531010-71 is interchangeable with the 11.3531010-70 by ports size.
Technical specification:
Working pressure, MPa (kgs/cm2): 0,65…0,85 (6,5…8,5)
Thread: М22Х1,5-7Н
Temperature range, °С: from minus 45 to plus 60
Weight, kg, not more than: 1,8
Initial sensitivity, MPa (kgs/cm2): 0,03 (0,3)
 Air Dispenser for Two-Line Trailer Brake System 11.3531010-81
Description:
Air Dispenser for Two-Line Trailer Brake System 11.3531010-81 is used in Single-Line Air Brake System of trailers and semi-trailers. Operated mechanically and ensures fast and controllable admission of compressed air into trailer's brake chambers. Features a mechanically operated valve for automatic trailer brake release.
It is a improved modification of the Air Dispenser 11.3531010-80, distinguishing by discharged valve system, which allows to decrease initial device sensitivity from 0,045 MPa to 0,03 MPa and consequently to decrease trailer (semi-trailer) air brake abrasion time. A distinguishing feature of this device is improved appearance and lesser steel intensity by using injection casting in body production without a price rise in comparison with 11.3531010-80.
Air Dispenser 11.3531010-81 is interchangeable with the 11.3531010-80 by ports size.
Technical specification:
Working pressure, MPa (kgs/cm2): 0,65…0,85 (6,5…8,5)
Thread: М22Х1,5-7Н
Temperature range, °С: from minus 45 to plus 60
Weight, kg, not more than: 1,8
Initial sensitivity, MPa (kgs/cm2): 0,03 (0,3)
 Relay Valve 11.3518010/-20
Description
Relay Valve 11.3518010/-20 is used in Air Brake Systems of trucks, buses, wheeled tractors, trailers and semi-trailers.
Operated pneumatically and ensures fast and controllable admission of compressed air into respective brake chambers or control lines.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Thread: М22Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 1,05
 Relay Valve 11.3518010-10
Description
Relay Valve 11.3518010-20 is used for fast and controllable admission (dismissal) of compressed air into respective brake chambers or control lines.
Compatible with Silencer.
Technical specification
Working pressure , MPa (kgs/cm2) - from 0,65 to 0,85 (from 6,5 to 8,5);
Initial insensitivity, MPa (kgs/cm2) - below 0,03 (0,3);
Thread – М22х1,5-7Н;
Temperature range, °С - from minus 50 to plus 60;
Weight, kg – 0,830.
 Fast Brake Release Valve 11.3518110
Description
Fast Brake Release Valve 11.3518110 is used in Air Brake Systems of trucks, buses, wheeled tractors, trailers and semi-trailers.
It is designed to decrease brake release time by accelerating air exhaust from actuators at the expense of reduced distance covered by air during exhausting process. Fast Brake Release Valve is compatible with Silencer 11.3590070 produced by PJSC "Poltava Automobile Unit Plant".
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,65-0,85 (6,5-8,5)
Maximum flow area equivalent to diameter of the hole, mm: 14
Start of air receipt at valve outlet, when valve inlet pressure is, MPa (kgs/cm2), not more than: 0,02 (0,2)
Pressure difference at valve’s outlet and inlet with increasing pressure, MPa (kgs/cm2), not more than: 0,02 (0,2)
Thread: М22Х1,5
Connecting torque of fittings with rubber seals at thread М22х1,5, N•m: 15...25
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 0,3
|
Hose Couplings
 Hose Couplings "PALM" type 100-3521110/111, 11.3521410/11, 11.3521510/11
Description
Hose Couplings "PALM" type 100-3521110/111 are used in Air Brake Systems of trucks, wheeled tractors, trailers and semi-trailers.
Hose Couplings are designed for fast and reliable connection of both air supply line and trailer brake control line to tractive vehicle's brake circuit under the two-line scheme.
Produced in following modifications:
Basic 100-3521110 (red), 100-3521111 (blue or yellow)
Automatic 11.3521410 (red), 11.3521411 (blue or yellow). Self-locks when disconnected, making additional disconnecting valve unnecessary
Filtering 11.3521510 (red), 11.3521511 (blue or yellow). Features a filtering element, making additional line filter unnecessary
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Thread: М22Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 0,275
 Main Filter 12.3511310-01
Description
Main Filter 12.3511310-01 is used in Air Brake Systems of trailers and semi-trailers.
Installed in supplying, controlling and connecting lines after hose couplings and hoses for the purpose of preventing ingress of dust and other contamination into trailer's brake gear.
Technical specification
Working pressure, MPa (kgs/cm2), 0,65…0,80
Thread: М22Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 0,42
 Hose Coupling with Relay Valve 11.3521110-02
Description
Hose Coupling with Relay Valve 11.3521110-02 is used in Air Brake Systems of trailers and semi-trailers.
It is designed to connect trailer's air brake line to tractive vehicle's brake circuit under the single-line scheme. Provides fast air exhaust from airline for the purpose of decreasing reaction time of trailer's brake gear during brake release.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Thread: М22Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 0,4
|
Auxiliary Devices
 Pressure Controll Valve 11.3122009-02
Description
Pressure Controll Valve with Limiting Valve is used in trucks and wheeled tractors with centralized tire pressure control system.
It is designed to provide air delivery and air bleed to/from tires for the purpose of rough-terrain performance improvement due to controlled air pressure in tires.
Technical specification
Working pressure, MPa (kgs/cm2): 0,65...0,85 (6,5...8,5)
Spool stroke, mm: 24
during air bleed, mm: 12
Conditional pass, mm: 5,5
Thread: К3/8"
Spool movement force, max, N (kgs): 100 (10)
Temperature range, °С: from minus 50 to plus 60
Dimensions, mm:
length 223
height 54
width 50
Weight, kg: 0,5
 Pressure Controll Valve 11.3122110
Description
Pressure Controll Valve is used in pneumatic break gear of vehicles. Provides air delivery and air bleed to/from air brake circuit.
Technical specification
Working pressure, MPa (kgs/cm2): 0,65…0,85 (0,65…8,5)
Spool stroke, mm: 24
during air bleed, mm: 12
Thread: К3/8"
Temperature range, °С: from minus 50 to plus 60
Weight, kg: 0,3
 Drain Valve 11.3513110/-10
Description
Drain Valve 11.3513110/-10 is used to force condensate drainage from the brake system's air receiver and, if needed, to bleed compressed air from the receiver.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Thread: М22Х1,5
Temperature range, °С: from minus 45 to plus 60
11.3513110 – with ring on pusher
11.3513110-10 – without ring on pusher
Weight, kg: 0,044
 Control Output Valve 13.3515310
Description
Control Output Valve is applied in Air Brake Systems of trucks, buses, wheeled tractors, trailers and semi-trailers.
It is used for compressed air remove from the system to connect it to diagnostic equipment or for compressed air remove for external consumers. Also it can be used for compressed air supply into external source system.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Thread:
for measuring device nut: М16Х1,5
for screwing valve: М22Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 0,06
 Control Output Valve 13.3515310-10
Description
Control Output Valve is used in Air Brake Systems of trucks, buses, wheeled tractors, trailers and semi-trailers.
Used for connecting diagnostic equipment for Air Brake System pressure control. The valve can also be used for air bleeding
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Thread:
for measuring device nut: М16Х1,5
for screwing valve: М22Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 0,06
 Disconnecting Valve 12.3520010/-10
Description
Disconnecting Valve 12.3520010 is used for blocking the airlines connecting the tractive vehicle with a trailer or a semi-trailer.
Modification 12.3520010-10 allows air bleed from the system when the valve is in blocking state.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Thread: kg 1/2"
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 0,45
 Disconnecting Valve 14.3520010/-10
Description
Disconnecting Valve 14.3520010 is used for blocking the airlines connecting the tractive vehicle with a trailer or a semi-trailer.
Modification 14.3520010 has a bleeder opening, allowing compressed air bleed from trailer or semi-trailer to atmosphere performing when the main is closed.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,65 – 0,85 (6,5 – 8,5)
Thread: М22Х1,5
Temperature range, °С: from minus 45 to plus 60
 Electrical-Pneumatic Valve 11.3745000-21
Description
Electro-Pneumatic Valve 11.3745000-21 is used in pneumatic systems of commercial vehicles and technological equipment for the purpose of airflow management in pneumatic circuits.
Available modifications:
11.3745000-21 featuring a threaded hole with tapered thread KG 1/8"
Technical specification
Conditional pass, mm.: 1,6
Working pressure of compressed air, MPa (kgs/cm2): 0,6…0,8 (6,0…8,0)
Reaction time, s.: 0,03
Type of current: directs
Voltage, V: 24
Power consumption, W: 7
Weight, kg: 0,35
Throughput, not less than, m3/hr: 0,08
 Wheel Valve 255Б - 4224110 Б
Description
Wheel Valve 255Б - 4224110 Б is used in trucks, wheeled tractors with centralized tire pressure control system.
Designed to connect and disconnect the tire to/from the source of compressed air. Features a valve for individual tire filling.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Thread: М18Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 0,4
 Fuel Regulating Valve 6322-1104650-01/-11
Description
Fuel Regulating Valve 6322-1104650-01/-11 is installed on vehicle's fuel tank and is used for switching fuel intake from the fuel tanks and fuel discharge from the engine into the fuel tanks.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,1 (1,0) Type: cork Thread: М16Х1,5 Temperature range, °С: from minus 45 to plus 60 Weight, kg:
257-1104650-01: 1,83
257-1104650-11: 1,94
 Silencer 11.3590070
Description
Silencer 11.3590070 is used in Air Brake Systems of trucks, buses, trolleybuses and wheeled tractors.
Installed on exhaust ports of air brake control valves.
Compatible with:
Brake Valves 100-3514008-01/-11/-21/-31, 11.3514108, 11.3514208-01/-11/-21/-31
Relay Valves 11.3518010-10
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,85 (8,5)
Connection diameter, mm: ¤28,9
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 0,06
|
Tractor Apparatus
 Hose Coupling “A”- type 12.3521010/-01
Description
Hose Coupling “A”- type 12.3521010/-01 is used for connecting trailer’s single-line air brake system as well as for automatic blocking of airflow when the heads are disconnected.
Technical specification
Working pressure, MPa (kgs/cm2), not more than: 0,8 (8,0)
Thread: М22Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 0,25
 Pressure Regulator 11.3512010-30
Description
Pressure Regulator 11.3512010-30 is used in Air Brake Systems of trucks, buses and wheeled tractors.
Provides pressure control of the air, supplied into vehicle’s brake system.
Technical specification
ON pressure, MPa (kgs/cm2): 0,65 (6,5)
OFF pressure, MPa (kgs/cm2): 0,85 (8,5)
Relief valve engagement pressure, MPa (kgs/cm2): from 0,85 to 1,0 (from 8,5 to 10,0)
Thread: К 3/8”
Air bleed valve thread: М16Х1,5
Temperature range, °С: from -45 to +60
Weight, kg: 0,70
 Pressure Regulator 11.3512010-40
Description
Pressure Regulator 11.3512010-40 is used in Air Brake Systems of trucks, buses and wheeled tractors.
Provides air pressure control, supplied into vehicle’s brake system.
Technical specification
ON pressure, MPa (kgs/cm2): 0,65 (6,5)
OFF pressure, MPa (kgs/cm2): 0,85 (8,5)
Relief valve engagement pressure, MPa (kgs/cm2): from 0,85 to 1,0 (from 8,5 to 10,0)
Thread: К 3/8”
Air bleed valve thread: М16Х1,5
Temperature range, °С: from -45 to +60
Weight, kg: 0,70
 Brake Valve 14.3514010
Description
Brake Valve 14.3514010 is used in single-line air brake systems of tractors.
Operated mechanically by pulling. The valve provides fast and controlled admission and exhaust of compressed air to/from control chambers of pneumatic apparatus of trailers’ brake systems.
Technical specification
Working pressure, MPa (kgs/cm2): 0,65…0,8 (6,5…8,0) Free rod stroke, mm: 1,0 – 2,0 Working rod stroke, mm: 10 – 12 Full rod stroke, mm: 13 – 14 Thread: K3/8” Temperature range, °С: from -45 to +60
 Rod 14.3514160/-10/-20/-30
Description
It is used in Brake Valve 14.3514010, which is used in single-line pneumatic driving gear of braking system and is mechanically operated by the rod.
Technical specification
Initial spring force, N, not more than: 210
Installation spring length, mm: 37±1,25
Weight, kg, not more than: 0,4
|
 Air Preparation Unit 11.3536006-10
Description:
Air Preparation Unit 11.3536006-10 is an alternative to Air Dryer ZB44 series with 4-circuit protection valve produced by «KNORR-BREMSE». It consists of Air Dryer and 4-circuit Protection Valve, which are connected by steel connecting pipe. Construction advantages are decreasing of assembling costs and enlargement of lay-out variants (attitude position of the protection valve can vary by valve rotation around a «22-22» teat axle.
Technical specification:
Compressor air discharge mode engagement pressure, MPa (kgs/cm2): 0,85+0,02 (8,5+0,2)
Compressor fill mode engagement pressure, MPa (kgs/cm2), min: 0,7 (7,0)
Pressure, limited by protection valve, MPa (kgs/cm2): 0,95…1,35 (9,5…13,2)
Thread: М22х1,5-7Н, М12х1,5-7Н
Temperature range, °С: from minus 45 to plus 60
Dew point reserve, °С, min: 15
Weight, kg: 5,5
Heater Element Specification:
Rated voltage, V: 24-3
Nominal power consumption, W: 100;
ON temperature, °С: 7-6
OFF temperature, °С: 27 ± 4
 Reverse-action Hand Brake Valve 11.3537510
Description:
Reverse-action Hand Brake Valve is used in pneumatic braking system of trucks, buses, trolleybuses and wheel tractors. Operated mechanically by turning the handle and provides controlled compressed-air bleed from the parking brake control bus or from the reserve brake control bus.
Reverse-action Hand Brake Valve 11.3537510 gives an opportunity to realize control testing of a truck’s hand brake efficiency for keeping vehicle on slope while a trailer is unbraked.
Technical specification:
Working pressure, MPa (kgs/cm2): 0,65...0,85 (6,5...8,5)
Maximum flow area equivalent to diameter of the hole, mm: 7
Thread, mm: М 14х1,5
Connecting torque of fittings with rubber seals at thread holes, N•m: 15...25
Working temperature range, °С: from minus 45 to plus 60
Weight, not more than, kg: 0,73
 Clutch Master Cylinder 11.1602010/-10
Description:
It is used for signal transmission between clutch pedal and pneumohydraulic booster.
Technical specification:
Stroke: 42 mm
Cylinder diameter: 32мм
Working pressure: 1,0 MPa (10,0 kgs/cm2)
Maximum pressure: 7,0 MPa (70,0 kgs/cm2)
 Clutch Servo 11.1609010
Description:
It is used for decrease of driver’s effort, while he declutches by pedal. This device decreases driver’s fatiguability and increases vehicles ergonomical characteristic by using energy of a compressed air.
Technical specification:
Working pressure, MPa (kgs/cm2): 0,65-0,85 (6,5-8,5)
Working pressure of the fluid: to 1MPa (10 kgs/cm2)
Maximum pressure: 12 MPa (120 kgs/cm2)
Conditional air flow area: more than 6mm
Force on the rod when air pressure is:
0,6 MPa (6,5 kgs/cm2) - not less than 5000 N (500 kgs)
0,8 MPa (8,0 kgs/cm2) - not less than 6200 N (620 kgs)
Full rod stroke, mm: 68-72
Temperature range, С°: from minus 40 to plus 60
Thread: М14x1,5, М16x1,5
Weight, kg, not more than: 5,1
 Foot Brake Valve with Pedal 121.3514308
Description:
The Brake Valve is used in pneumatic braking system of trucks, buses, trolleybuses and wheel tractors.
It is operated mechanically by suspended pedal, ensuring that the brake chambers in each of two circuits, as well as control chambers of other pneumatic apparatus of the Brake System, are filled with compressed air following appropriate filling speed and with appropriate tracking. Fastening surface is decreased. This devise has space-saving dimensions.
If one of the Brake System's circuits is depressurized, the Brake Valve provides controllable refill of the working circuit with compressed air.
Technical specification:
Working pressure, MPa (kgs/cm2): 0,65 – 0,85 (6,5 – 8,5)
Free pusher stroke, mm: 1,9 – 3,0
Full opening pusher stroke, mm: 8,4 – 10,8
Total pusher stroke, mm: 12,5 – 15,7
Thread: М22X1,5
Temperature range, °С: from minus 45 to plus 60
 Double-main Valve 12.3562010/-10
Description:
Double-Main Valve 12.3562010/-10 is used in Air Brake Systems of trucks, buses, wheeled tractors, trailers and semi-trailers.
It has two inputs and one output and provides fast air bypass from the input with bigger pressure to the output.
Technical specification:
Working pressure, MPa (kgs/cm2): 0,65…0,80
Thread: М22Х1,5
Temperature range, °С: from minus 45 to plus 60
Weight, kg: 0,42
 Electrical-Pneumatic Valve 12.3745000/-10/-30
Description:
Electrical-Pneumatic Valves 12.3745000 with 3 mm internal diameter and bayonet electro-cutoff point according to the DIN 72585-1 ensure reliable and waterproof bond. It is used in pneumatic systems of commercial vehicles and technological equipment for control stream of compressed air in pneumatic circuits. Electrical-Pneumatic Valves design allows to assemble them in blocks.
Technical specification:
Conditional pass, mm.: 1,6
Working pressure of compressed air, MPa (kgs/cm2): 0,6…0,8 (6,0…8,0)
Reaction time, s.: 0,03
Type of current: directs
Voltage, V: 24
Power consumption, W: 7
Weight, kg: 0,35
Throughput, not less than, m3/hr: 0,08
 Auxiliary Brake 12.3570010
Description:
It is used for braking by standing engine while fuel feeding is turned off.
Technical specification:
Working pressure, MPa (kgs/cm2): 0,65-0,85 (6,5-8,5)
Thread: М12х1,5
Damer movement angle: °65
Temperature range, °С: from minus 45 to plus 60
Weight, kg, not more than: 5,1
 Driver Seat Damper 260-6809109
Description:
It is used for smooth extinguishing of vertical driver’s seat oscillation.
Technical specification:
Maximum diameter, mm: 44
Outer diameter, mm: 22
Length in compressed state, mm: 190
The force of resistance, developed in shock absorbers
during compression and impact: 40±10 kgs
Rod movement speed, m/s: 0,226
Weight, kg: 0,2
|
CONSUMER GOODS
 Mincing Machine МА-С ГОСТ 4025-83 МББ-000-001
Designed for preparing minced meat and fish at home.
Performance: 32 kg/h.
Peak effort applicable to the handle during meat mincing: 2.9 kg.
Weight: 1.4 kg
 Juice extractor СБ-1-000
Squeeze ratio for juice with pulp:
Carrot - 25%
Apples - 55%
Tomatoes - 82%
Weight: 1.6 kg.
 Add-on for Mincing Machine ПМБ-1-000 ТО 37.366.151-92
Allows using Mincing Machine МА-С ГОСТ 4025-83 for making vegetable and fruit juice with pulp at home.
Weight: 0.3 kg.
 Juice Extractor Add-on ПСВ 10.000 ТО У 28.7-30601643-005-2002
Allows using Mincing Machine МА-С ГОСТ 4025-83 for making vegetable and fruit juice with pulp at home.
Connecting dimensions: bore diameter 54 mm.
Weight: 0.17 kg.
 Pelmeni Maker ПК 10.000 ТО З of Ukraine 0023212424-94
Appliance for making pelmeni of dough and minced meat.
Weight: 0.68 kg.
|
Українська
中文
English
We carefully consider the needs and requests of our customers and base our relationship on mutual interests.
In total volume of shipped products in 10 month of 2007 we exported 72,9%. Sales have grown in Russia (24,1%), Germany (44,8%), Moldova (400%), Kazakhstan (300%), Belorussia, Georgia, Latvia and other countries.
Now we have to work in conditions, when the demands of our customers are continuously growing. Ukraine is becoming more and more open for international cooperation, and this not only brings positive effect. Currently our market is flooded with cheap low-quality products, and it’s difficult to resist this tendency. That is why we decided to stand in the firm manner of competition, which means having precise aims, clear vision of our future and our mission, protecting the values of our customers and thus strengthen our competitiveness and increase profits.
